Linksys Extender RE7000 Setup and Reset Process
The Linksys RE7000 setup process is an important step if you want to avail the service of your Linksys Extender RE7000. The Linksys extender setup RE7000 can be done using two ways. Firstly by setting through the range extender mode and secondly as a wired range extender method(access point) mode. But anyway, for both cases to implement a router with a working internet connection is a must. Eventually, If you are still stuck with the question on how to set up the Linksys RE7000, this blog will provide some necessary details and ways regarding the same.
Setting up of RE7000 as a Wireless Range Extender
Linksys RE7000 Setup Using WPS (wifi protected setup)
If your router has a WPS button you can go for the WPS process mentioned below or, in case your router does not have WPS you can install using the browser-based setup discussed later in this blog. Read the guidelines given below for WPS Setup.
- Plug in the range extender into an electrical outlet by placing it closer to the router. You can relocate it later. Once the range extender is plugged in, the LED will start blinking in green colour for a minute at least.
- Now, wait for the LED to blink amber finally and then proceed further.
- Be ready to extend the 2.4GHz network. Press the WPS button on the router and on the range extender. The WPS button will glow up and the extender light will blink green.
- To verify if the connection, made was successful, watch the indicator LED in front. If it lights solid green, this means the connection made is successful but, if it turns amber this means that the connection is failed.
- Now, extend the 5GHz network. You can leave this step if your router does not support the 5GHz network. Hit the WPS button present on the side of your router again and then press the same on the extender. Verify the connection made by checking the lights.
- Finally, move the range extender to an optimal location from the router for better working and connection. Check the indicator LED for the connection quality. Solid green indicates that it is ready to use. Solid amber indicates it has a weak connection to the router. Blinking amber signifies that it is not connected to the router.
- Connect the devices to the extended network recently created.
The range extender is finally set up.
Linksys RE7000 Setup Using Browser-Based Setup
You can subscribe to this option if the WPS button is not present on your router or if you don’t want to install the extender using the WPS option. Follow the given steps for the same.
- Plugin the range extender.
- You can wait till the indicator LED on the front of the extender blinks amber.
- Now, connect to the range extender setup network.
- Launch the setup process now. You can do it using two ways either by using the gateway extender.Linksys.com or using the default IP address. Follow the on-screen instructions after that.
- In the end, you will be able to connect your devices with the extended network which you made just now
Setting up of RE7000 as a wired range extender(access point)
Browser-based setup
- To begin with the setup process, confirm if your router has an active internet connection. You must also have an ethernet cable to connect the range extender with the router.
- Plugin the Linksys extender into a power outlet.
- Wait for the blinking LED to switch from green to amber.
- Use an ethernet cable to connect the range extender and the LAN port of the router.
- Establish a connection with the Linksys extender setup network.
- To finally start the setup process, enter the web address extender.linksys.com in the address bar or fill in the default IP address. You will have to fill in the details for your login and then you will be directed to the web-based setup page.
- You can connect your wifi devices with the extended network just created.
Linksys RE7000 Reset Process
The Linksys RE7000 extender may have various issues like interrupted connections while its usage or when the web-based setup page of the extender is not accessible. The reset of the extender to the factory default settings will erase all the personalised settings which you made once. But, you should always have an option of backup for the device’s configuration settings. If you want to know the steps on how to reset Linksys RE7000 extender, read the instructions below.
Using the Reset button
Press and hold the reset button for at least 8 seconds. Now, power cycle the device to finish the reset process. The location of the reset button may vary with every model but mostly it’s on the back or bottom of the device.
Using the web-based setup page
After opening any web browser of your choice, access the web-based setup page of the range extender. Now, under the administration option, select the factory defaults. Hit the restore factory default button. For the final step, unplug the range extender from the power outlet and then leave it in the power-off mode for about 30 seconds. Plug it into the device afterwards. Click the restore configuration under the management sub-tab and finally click on the Save settings button.
Conclusion
The Linksys Extender RE7000 Setup and Reset Process can be performed now using the simple steps mentioned above. You can now go ahead and enjoy the seamless connection anywhere in the house/workplace. If you have any doubts, call our experts’ team now on the toll-free number and get the issues resolved. You also read the user manuals or the installation guides as well.